Concierge unpacking included with every mattress · To the room of your choice, packaging taken away

35cm hybrid · 13 layers

13 layers.
Each one earning
its place.

You are spending real money on something you cannot open. So here is every layer of the Perennial bed, what it is made of, and what it does for you once you are lying on it.

Onni London+ mattress in profile

35 centimetres

Twinbuild. Two parts,
closed with a zip.

15cm of comfort above, 20cm of support below. The top part comes out. The bottom part carries a 25 year guarantee.

400gsm

Coolweave cover

15cm

Comfort, removable

20cm

Sevencore

7

Support zones

35cm

Finished depth

Top to bottom

Every layer, stated

In the order you meet them, from the surface down to the frame.

01

Coolweave cover

400gsm viscose cool-knit · zip access all the way round

A 400gsm knitted cover, not a laminate. Knit moves air where a bonded surface holds it, so warmth leaves through the top rather than gathering under you.

It unzips the whole way round. That is how the comfort layer comes out, and it is the reason this mattress is renewed rather than replaced.

Coolweave cover, 400gsm
02

Coolcell

1cm · 28 density

The highest density we use anywhere in the build, and only 1cm of it. Gel infusion is what stops memory foam behaving the way memory foam usually does.

It contours to your shoulder and hip without holding the heat that contouring normally creates.

Coolcell at the surface
03

Comfort foam

1.5cm · grade 2030

The softness you feel in the first second. Softer and lower density than the gel above it, so the surface yields before the support underneath engages.

It is the difference between lying on a mattress and settling into one.

04

Wave-profile foam

2.5cm · 20 density

Cut into a wave rather than left flat. The profile creates channels through the middle of the comfort stack.

Air moves sideways through those channels instead of being trapped between two solid layers. It is a structural answer to heat, not a coating.

Wave-profile cut, visible at the edge
05

Nonwoven separator

25g

Keeps the foams above from bonding to the comfort layer below.

Without it, the stack above would fuse to the layer that has to lift out. This is why the comfort section still comes out cleanly years later.

06

Comfort face A

5cm · grade 2540

25 density at 40 hardness. The reverse surface.

Same density as the face below it, different hardness. Both last as long as each other.

The comfort layer sits above the core
07

Comfort face B

5cm · grade 2580

Same 25 density at 80 hardness. The side you sleep on as delivered.

Turn the layer over for the softer face. You do not choose a firmness when you order. The mattress arrives with both.

08

Nonwoven separator

70g

The release surface. The whole comfort section lifts off this.

It is the reason the comfort layer still lifts out cleanly in year 8.

09

Spring padding

Over the coils

You feel a surface, not 2,000 separate objects.

A pad over the coil tops so the springs stay felt as support, not as points.

10

Sevencore

20cm · 7 zones · 1.8 / 2.0mm wire · 2.2mm edge

Zone 2 is your shoulder. Zone 4 is your hip. Zone 6 is your leg. Those three are wound at 2.0mm because that is where a body lands hardest. Head, back, knee and feet sit on 1.8mm, because they do not. Two rows of 2.2mm wire sit around the edge.

Each spring moves alone, so one person turning over does not move the other side. Up to 2,000 springs.

Side panel, over Sevencore
11

Encased perimeter

8cm · 35 density

A dense foam wall around the entire spring unit, 35 density, 8cm deep.

You can sit on the edge to put your shoes on without sliding off it, and the usable sleeping surface runs to the seam rather than stopping short of it.

Encased perimeter and carry handle
12

Base padding

Under the coils

Protects the coil bases from the frame.

The springs sit on a pad, not directly on the slats, so the unit lasts the life of the guarantee.

13

Anti-slip underside

Full base

A gripped base rather than a plain fabric one.

It stays where you put it, on a slatted frame or a divan, without the annual shove back into position.

Quilted surface detail

What it adds up to

Softness you feel first.
Support you feel for
25 years.

The top 5cm are three foams doing three different jobs: Coolcell taking heat off your skin, immediate give, and airflow through the middle. Beneath them, 10cm of flippable comfort layer that lifts out.

Under all of it, Sevencore: 20cm of 7-zone pocket springs that will still be doing their job long after the layer above has been renewed twice.

The part that softens comes out. The part that holds you does not.

Adjust to Desire

If the feel is not right,
we make it right.

Sleep on it for a month. Then tell us how it should feel, softer or firmer, more give under the hip, whatever words you have. We send the layer that gets you there, with our compliments. Worth about £299.

Nothing goes back. Nothing is disassembled. You unzip the cover, lift the old layer out, drop the new one in.

100 nights to change your mind.

The outcome

A Perennial bed that becomes yours,
and stays that way.

  • The feelYou do not choose the feel. You discover it.
    Sleep on it for a month. Tell us how it should feel. We send the layer that gets you there.
  • ArrivingIt arrives finished.
    Concierge unpacking. Room of your choice. Unrolled onto your bed. Your old mattress leaves with the packaging.
  • 25 yearsIt stays right for 25 years.
    The part that softens comes out. That is Onni London+ Refit: the service that keeps a Perennial bed yours. The part that lasts, lasts.

Choose your size